Beratung:

Tel: 05373 920705
Mo-Fr 10-12 + 14-16

Startseite |  Kundenkonto Neue Artikel Kontakt
Suche
Kategorien
 Wir brauchen Platz !
 Akkus
 Elektronik
   Aktoren
   Bücher
   Devantech
   DFRobot
   Dimension Engineering
   DIY Drones
   E-Textilien
   Entwicklungstools
   Freetronics
   Gehäuse
   GPS
   IKA Logic
   Kabel
   Kelly Controls
   LEDs / LCDs
   Livid Instruments
   MaxBotix
   Mechanik
   NGX Technologies
   Pololu
   Programmiergeräte
   Prototyping
   RoboteQ
   Robotics
   Rogue Robotics
   Schnurlos
   Sensoren
   Servocity
   Sparkfun
     Neu
     Bausatz
     Breakout Boards
     Komponenten
     Port-O-Rotary
     Retail
     SFE Widgets
     Swag
     Tools
   Stromversorgung
   Wandler
 Modellbau
 Multicopter
 Zubehör


Sonderangebote...
Information
Zahlung und Versand
Neue Artikel
Datenschutz
Widerrufsbelehrung
AGB
Impressum
Batterieentsorgung

Arduino-Compatible PTH Kit Sparkfun DEV-10523Artikelnummer: SF-DEV-10523

 
24,35 €

Alle Preise inkl. MwSt.
zzgl. Versandkosten
  Anzahl:

Diesen Artikel haben wir 1x am Lager
Lieferzeit 1-5 Tage*
 
<p> <strong>Description:</strong> This kit contains everything you need to build your very own Uno-Compatible development board! Simply follow the Assembly Guide and after some basic soldering, you&#39;ll have made a fully-functional Arduino-compatible board (in fashionable SparkFun Red). The included ATmega328 comes pre-loaded with the Arduino &quot;Optiboot&quot; bootloader so you don&#39;t have to worry about loading the firmware, simply solder it together, connect an FTDI Basic and load your favorite Arduino sketch!</p> <p> <strong>Note:</strong> You will need either an FTDI Basic or FTDI cable to load code.</p> <p> <strong>Kit Includes:</strong></p> <ul> <li> 1 x Arduino-Compatible PTH Kit PCB</li> <li> 1 x ATMega328 with Optiboot bootlader</li> <li> 1 x MCP1700 3.3V Voltage Regulator</li> <li> 1 x 5mm Green LED</li> <li> 1 x 5mm Red LED</li> <li> 2 x 330Ohm Resistor</li> <li> 2 x 10kOhm Resistor</li> <li> 1 x 16MHz Crystal</li> <li> 2 x 22pF Ceramic Capacitors</li> <li> 5 x 0.1uF Ceramic Capacitors</li> <li> 2 x 100uF Electrolytic Capacitors</li> <li> 1 x LM7805 5V Regulator</li> <li> 1 x Diode 1N4001</li> <li> 1 x Resettable Fuse PTC</li> <li> 1 x 28-Pin DIP Socket (To seat your ATMega)</li> <li> 1 x Push Button Reset Switch</li> <li> 2 x 6-Pin Female Headers</li> <li> 2 x 8-Pin Female Headers</li> <li> 1 x 6-Pin Right Angle Header (To connect your FTDI Basic)</li> <li> 1 x 0.1uF Capacitor</li> <li> 1 x DC Barrel Jack</li> </ul> <p> <strong>Documents: </strong></p> <ul> <li> <a href="http://dlnmh9ip6v2uc.cloudfront.net/datasheets/Kits/Arduino-Compatible-PTH-v13.pdf" target="_blank">Schematic</a></li> <li> <a href="http://dlnmh9ip6v2uc.cloudfront.net/datasheets/Kits/Arduino-Compatible-PTH-v13.zip" target="_blank">Eagle Files</a></li> <li> <a href="http://dlnmh9ip6v2uc.cloudfront.net/datasheets/Kits/SFE03-0010-KitCard-ArduinoPTH-ReadersSpreads.pdf" target="_blank">Assembly Guide</a></li>
 
 
Dieser Artikel wurde am 19.07.2011 eingetragen.
 | Startseite |