Beratung:

Tel: 05373 920705
Mo-Fr 10-12 + 14-16

Startseite |  Kundenkonto Neue Artikel Kontakt
Suche
Kategorien
 Wir brauchen Platz !
 Akkus
 Elektronik
   Aktoren
   Bücher
   Devantech
   DFRobot
   Dimension Engineering
   DIY Drones
   E-Textilien
   Entwicklungstools
     .NET
     ADuC
     Android
     Arduino
     ARM
     AVR
     B-SQUARES
     Beagle
     Chumby
     Cirrus
     Cookie
     Coridium
     Cubieboard
     Cypress
     Electronic Brick
     FAT
     FPGA
     Gadgeteer
     Grove
     Intel®
     iPod
     LinkIt ONE
     LPC
     MAXQ
     mbed
     MSP
     pcDuino
     PIC
     PICAXE
     Propeller
     PSoC
     Raspberry Pi®
     Roomba
     SAM
     ST
     STAMP
     Teensy
     TMS
     USB
     Virt2Real
     Wiring
     WIZnet
     Xadow
     XMOS
     Zune
   Freetronics
   Gehäuse
   GPS
   IKA Logic
   Kabel
   Kelly Controls
   LEDs / LCDs
   Livid Instruments
   MaxBotix
   Mechanik
   NGX Technologies
   Pololu
   Programmiergeräte
   Prototyping
   RoboteQ
   Robotics
   Rogue Robotics
   Schnurlos
   Sensoren
   Servocity
   Sparkfun
   Stromversorgung
   Wandler
 Modellbau
 Multicopter
 Zubehör


Sonderangebote...
Information
Zahlung und Versand
Neue Artikel
Datenschutz
Widerrufsbelehrung
AGB
Impressum
Batterieentsorgung

Development Board for AT90USB162 Sparkfun DEV-08857Artikelnummer: SF-DEV-08857

 
26,91 €

Alle Preise inkl. MwSt.
zzgl. Versandkosten
  Anzahl:

Diesen Artikel haben wir 1x am Lager
Lieferzeit 1-5 Tage*
 

Description: AT90USB162 is the easiest way to add USB functionality to your next device. Atmel provide free open source HID (mouse, keyboard) and CDC (USB-to-RS232) code and on top of this the AT90USB162 with the same cost as the ATMega16. Includes USB connector and circuit, external power supply if your circuit require more power than 100mA, button, status LED, and reset button.

All AT90USB162 ICs come from Atmel pre-programmed with bootloader, which allows code to be programmed inside the chip without any external programmer, just download the FLIP software from Atmel web site and load your HEX code inside AT90USB162. To enter the bootloader mode you should press and hold BUT button, then press and release RST button. If you preffer to use ICSP programmer note that only AVR-ISP-MK2 supports the AT90USB162 as these are pretty new devices. AVR Dude will probably add support soon. The AT90USB162 supports only debug Wire not JTAG, so to debug it you should have the expensive AT-JTAGICE-MK2.

Features:

  • AT90USB162 microcontroller with 16KB Flash, 512B RAM, 512B EEPROM
  • ICSP 5x2 pin connector for in-circuit programming with AVR-ISP-MK2 (you generally don't need to use ICSP as you can program via USB)
  • Debug Wire could be performed by 3 wires connected to ICSP (AT-JTAGICE-MK2 have such lose wire connector which to be used, you need VCC, GND, RST signals only)
  • USB 2.0 Full speed connector
  • User button BUT (can be used to enter bootloader mode after reset)
  • Reset button RST
  • Takes power from USB no need for external adapter
  • External power supply and voltage regulator if USB can't provide enough power
  • Quartz crystal oscillator circuit 8Mhz
  • Extension pin headers for each uC pin
  • Four mounting holes 3.3 mm (0.13")
  • Grid 100 mils
  • GND bus
  • Vcc bus
  • FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print
Dimensions: 100x80 mm (3.9x3.15")

Documents:

Software:

 
 
Dieser Artikel wurde am 09.11.2009 eingetragen.
 | Startseite |