Beratung:

Tel: 05373 920705
Mo-Fr 10-12 + 14-16

Startseite |  Kundenkonto Neue Artikel Kontakt
Suche
Kategorien
 Wir brauchen Platz !
 Akkus
 Elektronik
   Aktoren
   Bücher
   Devantech
   DFRobot
   Dimension Engineering
   DIY Drones
   E-Textilien
   Entwicklungstools
     .NET
     ADuC
     Android
     Arduino
     ARM
     AVR
     B-SQUARES
     Beagle
     Chumby
     Cirrus
     Cookie
     Coridium
     Cubieboard
     Cypress
     Electronic Brick
     FAT
     FPGA
     Gadgeteer
     Grove
     Intel®
     iPod
     LinkIt ONE
     LPC
     MAXQ
     mbed
     MSP
     pcDuino
     PIC
     PICAXE
     Propeller
     PSoC
     Raspberry Pi®
     Roomba
     SAM
     ST
     STAMP
     Teensy
     TMS
     USB
     Virt2Real
     Wiring
     WIZnet
     Xadow
     XMOS
     Zune
   Freetronics
   Gehäuse
   GPS
   IKA Logic
   Kabel
   Kelly Controls
   LEDs / LCDs
   Livid Instruments
   MaxBotix
   Mechanik
   NGX Technologies
   Pololu
   Programmiergeräte
   Prototyping
   RoboteQ
   Robotics
   Rogue Robotics
   Schnurlos
   Sensoren
   Servocity
   Sparkfun
   Stromversorgung
   Wandler
 Modellbau
 Multicopter
 Zubehör


Sonderangebote...
Information
Zahlung und Versand
Neue Artikel
Datenschutz
Widerrufsbelehrung
AGB
Impressum
Batterieentsorgung

XMega100 BreakoutArtikelnummer: SF-BOB-09546

XMega100 Breakout
19,22 €

Alle Preise inkl. MwSt.
zzgl. Versandkosten
  Anzahl:

Wir bestellen diesen Artikel für Sie. Wenn Sie heute bestellen, wird er am 08.10.2014 bei uns eintreffen.
Lieferzeit ab dann 1-5 Tage*
 

Description: This is a breakout board for the 100-pin TQFP package of Atmel's ATxmega128A1. The ATxmega128A1 is a low power, high performance and peripheral rich CMOS 8/16-bit microcontroller based on the AVR enhanced RISC architecture.

Among the chip's many features are 128kB of flash memory, 8 kB SRAM, 78 I/O pins, eight 16-bit timers, sixteen 12-bit ADCs, four 12-bit DACs, eight USART, four SPI and four TWI interfaces. This powerful chip can process up to 32 MIPS when running at its maximum clock speed of 32MHz. The operating voltage of the xmega is 1.6 to 3.6VDC.

All VCC pins of the ATxmega128A1 are connected together and brought out to a single header pin, same goes for the GND and AVCC pins of the chip. We've also included decoupling capacitors, and a red power indicator LED; but beyond those we've tried to keep the board as simple and straightforward as possible. If you want to start developing with this chip, but don't want to deal with soldering it, this is the board for you!

Note: This board ships with the example code shown below and the JTAGEN bit set to 1 (JTAG disabled, PDI enabled).

Features:

  • All pins of the ATxmega128A1 broken out to 0.1" spaced pins
  • 0.1uF decoupling capacitors placed near VCC inputs of the chip
  • 2x3 AVR ICSP connector broken out
  • Red power indicator LED
  • ATxmega128A1 Features:
    • High-performance, low-power 8/16-bit microcontroller
    • 1.6 - 3.6 VDC operating voltage
    • 128 KBytes Flash
    • 8 KBytes boot code
    • 2 KBytes EEPROM
    • 8 KBytes SRAM
    • 4 DMA channels
    • 32 MHz maximum clock frequency
    • 78 programmable I/O pins
    • Eight 16-bit timers
    • Eight USARTs, four SPI, and four TWI interfaces
    • Two Eight-channel (16), 12-bit, 2 Msps Analog to Digital Converters
    • Two Two-channel (8), 12-bit, 1 Msps Digital to Analog Converters
Dimensions:
  • 2.20 x 2.20" (55.88 x 55.88mm)
Documents:
 
 
Dieser Artikel wurde am 11.02.2010 eingetragen.
 | Startseite |