Beratung:

Tel: 05373 920705
Mo-Fr 10-12 + 14-16

Startseite |  Kundenkonto Neue Artikel Kontakt
Suche
Kategorien
 Wir brauchen Platz !
 Akkus
 Elektronik
   Aktoren
   Bücher
   Devantech
   DFRobot
   Dimension Engineering
   DIY Drones
   E-Textilien
   Entwicklungstools
     .NET
     ADuC
     Android
     Arduino
     ARM
     AVR
     B-SQUARES
     Beagle
     Chumby
     Cirrus
     Cookie
     Coridium
     Cubieboard
     Cypress
     Electronic Brick
     FAT
     FPGA
     Gadgeteer
     Grove
     Intel®
     Intel® Edison
     iPod
     LinkIt ONE
     LPC
     MAXQ
     mbed
     MSP
     pcDuino
     PIC
     PICAXE
     Propeller
     PSoC
     Raspberry Pi®
     Roomba
     SAM
     ST
     STAMP
     Teensy
     TMS
     USB
     Virt2Real
     Wiring
     WIZnet
     Xadow
     XMOS
     Zune
   Freetronics
   Gehäuse
   GPS
   IKA Logic
   Kabel
   Kelly Controls
   LEDs / LCDs
   Livid Instruments
   MaxBotix
   Mechanik
   NGX Technologies
   Pololu
   Programmiergeräte
   Prototyping
   RoboteQ
   Robotics
   Rogue Robotics
   Schnurlos
   Sensoren
   Servocity
   Sparkfun
   Stromversorgung
   Wandler
 Modellbau
 Multicopter
 Zubehör


Sonderangebote...
Information
Zahlung und Versand
Neue Artikel
Datenschutz
Widerrufsbelehrung
AGB
Impressum
Batterieentsorgung

40 Pin PIC Development Board with USB Sparkfun DEV-00022Artikelnummer: SF-DEV-00022

40 Pin PIC Development Board with USB Sparkfun DEV-00022
32,29 €

Alle Preise inkl. MwSt.
zzgl. Versandkosten
  Anzahl:

Wir bestellen diesen Artikel für Sie. Wenn Sie heute bestellen, wird er am 04.11.2014 bei uns eintreffen.
Lieferzeit ab dann 1-5 Tage*
 

Description: 40 Pin Development board with built-in USB connection. Power and serial communications are provided by the FTDI USB<->RS232 converter chip. You don't have to do anything! Connect the USB cable from your computer to the board and a new serial com port will install under Windows.  Also includes socket for I2C EEPROM - complete with pull-up resistors and connections to PIC pins. Perfect for basic debugging and serial data logging applications.

  • FR-4, 0.062" (1.5 mm), green solder mask, white silkscreen component print
  • Dimensions 3.9x3.15" (100x80 mm)
  • Four mounting holes
  • USB 'B' Type Connector
  • 5V (up to 500mA) provided through USB port
  • ICSP/ICD connector for programming with PIC Programmers and Debuggers (for PICs with ICD support)
  • RS232 communication provided through USB port via FTDI FT232M IC
  • LED to RA0 through jumper
  • Reset button/circuit
  • General purpose button
  • 20MHz quartz crystal oscillator with filtering capacitors
  • DIL40 microcontroller socket
  • DIL8 EEPROM socket with 2.2K pull-up on SDA
  • Extension slot on every uC pin
  • Gird 100 mils
  • GND bus
  • Vcc bus

Documents: Schematic, PIC ICSP connector

Warning: Do not attach a dongle ICSP programmer while the board is attached to the USB port: the PG1 and PG2C programmers can cause the power supply circuit to over-heat.

Board does not come with PIC installed. Please see a list of related ICs below.

 
 
Dieser Artikel wurde am 09.11.2009 eingetragen.
 | Startseite |