Beratung:

Tel: 05373 920705
Mo-Fr 10-12 + 14-16

Startseite |  Kundenkonto Neue Artikel Kontakt
Suche
Kategorien
 Wir brauchen Platz !
 Akkus
 Elektronik
   Aktoren
   Bücher
   Devantech
   DFRobot
   Dimension Engineering
   DIY Drones
   E-Textilien
   Entwicklungstools
     .NET
     ADuC
     Android
     Arduino
     ARM
     AVR
     B-SQUARES
     Beagle
     Chumby
     Cirrus
     Cookie
     Coridium
     Cubieboard
     Cypress
     Electronic Brick
     FAT
     FPGA
     Gadgeteer
     Grove
     iPod
     LPC
     MAXQ
     mbed
     MSP
     pcDuino
     PIC
     PICAXE
     Propeller
     PSoC
     Raspberry Pi®
     Roomba
     SAM
     ST
     STAMP
     Teensy
     TMS
     USB
     Virt2Real
     Wiring
     WIZnet
     Xadow
     XMOS
     Zune
   Freetronics
   Gehäuse
   GPS
   IKA Logic
   Kabel
   LEDs / LCDs
   Livid Instruments
   MaxBotix
   Mechanik
   NGX Technologies
   Pololu
   Programmiergeräte
   Prototyping
   RoboteQ
   Robotics
   Rogue Robotics
   Schnurlos
   Sensoren
   Sparkfun
   Stromversorgung
   Wandler
 Modellbau
 Multicopter
 Zubehör


Sonderangebote...
Information
Zahlung und Versand
Neue Artikel
Datenschutz
Widerrufsbelehrung
AGB
Impressum
Batterieentsorgung

USB Bit Whacker - 18F2553 Development Board Sparkfun DEV-00762Artikelnummer: SF-DEV-00762

USB Bit Whacker - 18F2553 Development Board Sparkfun DEV-00762
19,22 €

Alle Preise inkl. MwSt.
zzgl. Versandkosten
  Anzahl:

Wir bestellen diesen Artikel für Sie. Wenn Sie heute bestellen, wird er am 26.04.2014 bei uns eintreffen.
 

Description: The USB Bit Whacker is a spectacular little development board featuring the PIC18F2553. Based on the work of Brian Schmalz, the UBW is a small board with a command interpreter for basic input and output control. When attached to a Windows/Max OS X/Linux computer, the UBW will show up as an RS232 Com port! You control the individual I/O pins on the PIC through simple serial commands. Board comes fully tested, preprogrammed, and assembled as shown.

The 18F2553 also comes pre-programmed with a USB bootloader. This means you can create HEX files using any compiler or assembler (C18, CC8e, SDCC) and then load that HEX file onto the PIC without an external programmer - directly over USB! Power is obtained over USB.

Please download the Microchip USB Bootloader below. Please see the UBW home page for more information.

You may start with downloading and installing the latest release of Microchip USB Framework Installation file. The Release Notes provide details on the location of the Comunications Device Class (CDC) RS-232 Emulation driver INF file location. When installed the S1 LED will begin to blink.

Features:
  • Reset Button
  • General Input Button (also used to enter program mode during a reset)
  • mini-USB Connection
  • 16 General I/O
  • TX/RX (can be used as a USB to UART converter board)
  • 24MHz Resonator
  • Two Status LEDs
  • Preprogrammed with Bootloader and UBW_D firmware

Dimensions: 1.0x1.6"
Documents:

 
 
 | Startseite |